Kenneth Young
  • Male
  • La Plata, MD
  • United States
Share Twitter

Kenneth Young's Groups

 

Kenneth Young's Page

Latest Activity

Kenneth Young posted blog posts
May 12
Kenneth Young commented on Manfred Dickgiesser's blog post T-Rex 450 loiter APM 2.0 MediaTek MT3329 and barometer
"Very cool! Traditional helicopters are still and will always be my favorite. I have one question. How and where do you fit everything on the 450? I have a EXI 450 and could barely fit the receiver and speed controller in it."
Sep 1, 2012
Kenneth Young commented on Christiaan van Vollenstee's blog post TH9X Flight Mode Upgrade
"If you are even remotely toying with the idea of purchasing the kit do it. I purchased one (not yet received) and can't wait to install it. I currently have my radio setup with 6 flight modes using the 3 position "Aux. 3" & the 2…"
Jul 9, 2012
Kenneth Young commented on CyborgCNC's blog post New Heavy Lift QuadCopter Frame from HH
"They should call it IFSB (Inverted Flying Salad Bowl) :-)"
May 31, 2012
Kenneth Young commented on wayne garris's blog post techpod prototype
"VERY NICE! It looks like the perfect platform to replace my HK FPV168 which is so tail heavy it's not funny."
May 28, 2012
Kenneth Young commented on Brian's blog post 3.3v Power Supply Options - What's recommended?
"RadioShack® Adjustable-Voltage Regulator LM317T $2.99 http://www.radioshack.com/product/index.jsp?productId=2062601 Datasheet: javascript: http://www.datasheetcatalog.org/datasheet2/1/03cgthpfat4t4ly5kfp5lpwladfy.pdf Probably $8-10 in…"
Jan 23, 2012
Kenneth Young commented on Gordon's blog post Mode Switch Setup for Turnigy 9x
"I had to adjust my end points on my flaps and ailerons and now all of my flight mode settings are off again, Uncle!!! I've ordered the Add-on Board with built-in Programmer so I can update the firmware and hopefully resolve…"
Jul 27, 2011
Kenneth Young commented on Gordon's blog post Mode Switch Setup for Turnigy 9x
"I started from scratch again. Reset radio settings to defaults and it worked out this time but while assigning flight modes I couldn’t set them up the way I wanted. The switches on this radio must be in their default positions when the radio…"
Jul 13, 2011
Kenneth Young commented on Gordon's blog post Mode Switch Setup for Turnigy 9x
"I followed these instructions to the tee and everything went ok except step 7. I can't adjust the UPRATE value high enough to get a pulse rate of 1295. The lowest it will go is 1360 @ -100 and is throwing everything off. I'm using a…"
Jul 11, 2011

Profile Information

About Me:
IT, RC airplanes and helicopters
Tell us a bit about your UAV interest
Just for fun!
Hometown:
La Plata, MD

Kenneth Young's Blog

Flashing the Atmega328p (PPM encoder/failsafe) with Arduino Mega 2560

Posted on May 12, 2013 at 11:30am 0 Comments

Updating the PPM encoder firmware on APM1 with an Arduino Mega 2560

       

In order to perform this firmware update there are two programmer options given on the…

Continue

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join DIY Drones

 
 
 

Social Networking

Contests

Season Two of the Trust Time Trial (T3) Contest has now begun. The fourth round is an accuracy round for multicopters, which requires contestants to fly a cube. The deadline is April 14th.

A list of all T3 contests is here

Groups

Advertisement

© 2013   Created by Chris Anderson.   Powered by

Badges  |  Report an Issue  |  Terms of Service