DIY Drones

Antonio Watkins
  • Male
  • Tucson, AZ
  • United States
Share 

Antonio Watkins's Friends

Antonio Watkins's Discussions

I've never flawn an RC plane before. What simulator should I get to start out?

Great planes Real flight. That is the only one that comes to mind right now but there are others.

Replied Dec 7

predator plans

I would like a set of the preditor plans as well. Can you forward them to me as well?.

Replied Dec 4

in expensive note book computer to programm the Ardu pilot in the field
1 Reply

Does anybody know of a in expensive note book computer to program the Ardu pilot in the field?.

Started this discussion. Last reply by HappyKillmore Dec 1.

Shield board v2
1 Reply

Does anybody know if the shield board V2 comes with the male and female pins. I do not need all the hardware that comes with the V2 shield kit.

Started this discussion. Last reply by Thomas J Coyle III Nov 27.

 

Antonio Watkins's Page

Latest Activity

Antonio Watkins replied to mark's discussion 'I've never flawn an RC plane before. What simulator should I get to start out?'
Great planes Real flight. That is the only one that comes to mind right now but there are others.
December 6
Antonio Watkins replied to Todd Smith's discussion 'predator plans'
I would like a set of the preditor plans as well. Can you forward them to me as well?.
December 3
HappyKillmore replied to Antonio Watkins's discussion 'in expensive note book computer to programm the Ardu pilot in the field'
Asus Netbook? $250 http://www.bestbuy.com/site/Asus+-+Eee+PC+Netbook+with+Intel%26%23174%3B+Atom%26%23153%3B+Processor+-+Midnight+Blue/9556811.p?id=1218124205088&skuId=9556811
November 30
Antonio Watkins added a discussion
in expensive note book computer to programm the Ardu pilot in the field
Does anybody know of a in expensive note book computer to program the Ardu pilot in the field?.
November 30
Thomas J Coyle III replied to Antonio Watkins's discussion 'Shield board v2'
Antonio, I just finished building the new v2 Shield board and it came with the female headers and the connector for the thermopile cable. Hope this helps. Regards, TCIII
November 26
Antonio Watkins added a discussion
Shield board v2
Does anybody know if the shield board V2 comes with the male and female pins. I do not need all the hardware that comes with the V2 shield kit.
November 26
Antonio Watkins replied to Antonio Watkins's discussion 'problems with down loading code'
Just tried loading the code trough the shield. Would not upload. Just said uploading to I/O board. Never completed it. I then hooked the gps back to it to see if the code had loaded. GPS would not lock. I then took the shield board off again to load…
November 26
Antonio Watkins replied to Antonio Watkins's discussion 'problems with down loading code'
when I get back home I will see if I can load the code with the sheild. If I cant, it probably is the shield and will have to order another one.
November 26
Chris Anderson replied to Antonio Watkins's discussion 'problems with down loading code'
Maybe a soldering error with the shield? Can you load the code with the sheild on?
November 26
Antonio Watkins replied to Antonio Watkins's discussion 'problems with down loading code'
works without shield and the code is already set to 1
November 26
Antonio Watkins replied to Antonio Watkins's discussion 'problems with down loading code'
It woks without the sheild.
November 26
Chris Anderson replied to Antonio Watkins's discussion 'problems with down loading code'
Try it without the shield.
November 26
Antonio Watkins replied to Antonio Watkins's discussion 'problems with down loading code'
Yes there could be a problem with the top board?.
November 26
Antonio Watkins replied to Antonio Watkins's discussion 'problems with down loading code'
I opened the config tool now with the top board connected. My home position is listed on the map, I click on the map for way points then I click write. I then get a message that says write successful. Is this how it suppose to work?
November 26
Antonio Watkins replied to Antonio Watkins's discussion 'problems with down loading code'
I went to arduine 0017, hardware, library, ardu pilot, H file, first line is set to 1
November 26
Chris Anderson replied to Antonio Watkins's discussion 'problems with down loading code'
If you're using the V2 board (blue), did you change the easystar.h file to reflect that? (line 1-1)
November 26

Comment Wall

  • No comments yet!

You need to be a member of DIY Drones to add comments!

Join this Ning Network

 
 
 

© 2009   Created by Chris Anderson

Badges  |  Report an Issue  |  Privacy  |  Terms of Service

Sign in to chat!