Ardupilot Shield V2 schematics?

Hey all,

just received the new Ardupilot Shield V2. Just looked around a bit on the site and didn't find any schematic of it. Will this become available soon?

Ciao,

Rik

▶ Reply to This

Replies to This Discussion

Permalink Reply by Donny on October 22, 2009 at 8:09am: And will there be an update to the manual - http://docs.google.com/View?id=ddjmqgw3_43gm6gvggf; ▶ Reply to This

Permalink Reply by Rik Vlaming on October 25, 2009 at 3:51pm: The schematics and board-layout are available now :) Assembled the board without remaining questions, and ready to give it a new home in a Twinstar :)

Some quick links:
Schematic
Layout; ▶ Reply to This

Permalink Reply by Darro Lin on October 26, 2009 at 10:29pm: I ordered this board as the economic option before the version with the 3.3v regulator was available. I want to solder on the 3.3v regulator now. I'm looking at the schematic... I need to add C4, C5, and U3. What part should I use for U3? I don't see a part number? Thanks!; ▶ Reply to This

Permalink Reply by Multimull on November 4, 2009 at 5:25am: hi All,

I am just clicking together my first order @ the DIYdrones store, planning to build my firest Ardupilot on EZ* platform.
Ive read lots op post here on the forum and RCG as wel, so I am fully confidiend in getting it up&flying in no-time, also with al the good support you guys all bring into the community!

My question is: planning to order the V2 shield (http://store.diydrones.com/ProductDetails.asp?ProductCode=BR%2D0002...) is this board INCLUDING the pressure sensor?

Thx for your advise!; ▶ Reply to This

Permalink Reply by Chris Anderson on November 4, 2009 at 5:41am: Yes, it includes the pressure sensor.; ▶ Reply to This

Permalink Reply by shawn vatcher on November 4, 2009 at 7:11pm: anyone having troubles getting signal lock with this shield, cant seem to get it. im useing the em406 useally locks on greeat; ▶ Reply to This

Permalink Reply by Michel Lubbers on November 7, 2009 at 10:27am: Hi Shawn,

You have to download the newest V2.4 firmware.

http://code.google.com/p/ardupilot/downloads/list

Good luck!

Michel; ▶ Reply to This

Permalink Reply by Chris Anderson on November 7, 2009 at 12:08pm: Also select the right shield in the config file (1-1); ▶ Reply to This

Permalink Reply by Hessel on November 14, 2009 at 3:08am: What are the limitations of the V1 shield I have v.s. the new V2 shield ?; ▶ Reply to This

Permalink Reply by Richard Green on November 14, 2009 at 8:41am: Michel,

I have just bought the Ardupliot board, the v2 shield and a em406 GPS. I wanted to use the 2.1 ardupilot code as I do not have a z-sensor (I have the x-y sensors from my FMA CPD4). Can I use the v2 shield with the 2.1 ardupilot code or can I alter the 2.4 ardupilot code to just use the x-y sensors and do the 'tail-up' field calibration?

Thanks
Richard; ▶ Reply to This

Permalink Reply by Faisal Shah on November 14, 2009 at 8:14pm: Can I get the eagle files for this. I've asked a few times in a couple of different places ... Is there any issue in posting the eagle schematic and layout? How about the footprint for the pressure sensor?; ▶ Reply to This

Permalink Reply by Chris Anderson on November 14, 2009 at 8:59pm: We don't distribute Eagle files, I'm afraid.; ▶ Reply to This